Record Details

Studies On The Effect Of Closed Loop Controls On The Stability Of High Repetition Rate Copper Vapour Laser Pumped Dye Laser

Electronic Theses of Indian Institute of Science

View Archive Info
 
 
Field Value
 
Title Studies On The Effect Of Closed Loop Controls On The Stability Of High Repetition Rate Copper Vapour Laser Pumped Dye Laser
 
Creator Saxena, Piyush
 
Subject Dye Laser
Copper Vapour Laser
Closed Loop Controls
Optical Resonators
Dye Laser Stability
CVL
Metal Vapour Laser
Applied Optics
 
Description Copper vapour laser (CVL) pumped high repetition rate narrow bandwidth dye laser is an important source of tunable radiation. It finds numerous applications in spectroscopic investigations and selective material processing like atomic vapour laser isotope separation (AVLIS). Being wavelength selective in these applications stability of the output wavelength and bandwidth are extremely important. The stability of these parameters depend upon the refractive index fluctuation of the dye medium, due to pump beam induced temperature gradients, dye solution flow, and mechanical stability of optical components. Precise measurement of wavelength and bandwidth of a dye laser and control over parameters governing the variations are important for any stable dye laser system.
In this thesis, details of investigations carried out on a Rhodamine 6G dye laser for obtaining stable wavelength and output power are presented. Parameters that affect the stability were identified, monitored and put on close loop control to achieve the desired stability. Pump beam i.e. CVL optical power, dye flow rate and dye solution temperature are mainly these parameters. CVL power is mainly a function of input electrical power and pressure of the buffer gas inside the tube. To monitor and regulate these parameters, different sensors and actuators were selected and interfaced with a master slave topology based data acquisition and control system. The DAQ and control system is designed around a micro controller card based on advanced CPU P80552 and has on chip 8 channel 10 bit multiplexed analog input, 16 TTL digital inputs and 16 digital outputs. It works as slave and PC as master. Following closed loops were designed and incorporated to maintain a stable output:
a. Average output of CVL was maintained constant by regulating the electric input power through closed loop control.
b. The buffer gas pressure was monitored with a semiconductor pressure sensor and was regulated using pulse width modulation.
c. Temperature of the dye solution was monitored with PT100 and was controlled using proportional controller.
d. Flow rate of dye solution was controlled using a variable frequency drive (VFD) for the dye circulation pump.
e. The dye laser wavelength was monitored by using a high resolution spectrograph and pixel position of the peak from CCD image obtained from spectrograph is used for feedback correction using a pico motor.
In the present work with application of the above-mentioned input power and pressure loops, a stable output of CVL, is achieved. Variations in power and pulse width of CVL are got limited to within 2%, from 10% when CVL system was working unregulated. This control system does the line regulations and corrects the input electrical power if variations in discharge current occur due to pressure variation. Every dye cell has limits on flow rate because of its geometry. With flow and temperature control dye cell was characterized to work with lower linewidth. VFD (variable frequency drive) is used for flow regulation. Finally active control on set wavelength was also achieved with resolution of 0.01nm accuracy. Measurement of wavelength was done with 0.3 m, 0.054 nm resolution spectrograph. Closed loop pico motor with 30 nm per step linear resolution was used for wavelength control.
The thesis is organized in four chapters. First chapter presents a brief introduction to high repetition rate CVL pumped dye laser, operation of a CVL and parameters affecting the dye laser stability and their control schemes. Literature survey in this chapter is focused on different control mechanisms used with such lasers. Second chapter describes the laser system and interfacing of data acquisition system used for experimental setup. Closed loop controls for different parameters are described in this chapter. It also describes the software algorithms developed for this work. Third chapter presents experimental results and analysis with discussion on performance of the control loops. Finally the conclusion is given and few suggestions are made for further work.
 
Contributor Rao, K Narasimha
Abhinandan, Lala
 
Date 2009-04-01T10:21:08Z
2009-04-01T10:21:08Z
2009-04-01T10:21:08Z
2006-10
 
Type Thesis
 
Identifier http://hdl.handle.net/2005/444
 
Language en_US
 
Relation G20953