Record Details

Mechanical and Corrosion Properties of Selective Laser Melted Alloys

Electronic Theses of Indian Institute of Science

View Archive Info
 
 
Field Value
 
Title Mechanical and Corrosion Properties of Selective Laser Melted Alloys
 
Creator Suryawanshi, Jyoti Balaji
 
Subject Laser Melted Alloys
SLM Alloys
Al-12Si Alloy
Selective Laser Melting (SLM)
316L Stainless Steel
Selective Laser Melted Alloys
18(Ni) 300-grade Maraging Steel
Materials Engineering
 
Description Selective laser melting (SLM) of metallic powders is an additive manufacturing technique that is widely employed to produce 3D components, and is fast becoming an important method for manufacturing near-net shape and complex metallic parts. In this thesis, a comprehensive investigation on the effect of SLM on the mechanical and corrosion properties of the Al-12Si (AS), 316L stainless steel (SS), and 18(Ni)-300 grade managing steel (MS) is investigated, with particular emphasis on the developing (micro- as well as mesa-)structure -property correlations. Detailed microstructural characterization combined with quasi-static tensile, fracture toughness, fatigue crack growth, and unmatched fatigue tests were conducted. The effect of post-SLM heat treatment as well as the scanning strategy (linear vs. checker board hatch style) was examined and the results are compared with those of conventionally manufactured (CM) counterparts. The SLM alloys exhibit a mesostructured, in addition to the fine cellular structure along the boundaries. In a case of SLM-AS, the fine cellular structure imparts higher strength at the cost of ductility, while the mesostructured, which arises due to the laser track hatching, causes the crack path to be tortuous, and in turn leads to substantial increase in fracture toughness. This imparts significant anisotropy to the toughness while tensile properties are nearly-isotropic.
The experimental results of SLM-SS also show that higher tensile strengths properties with a marked reduction ductility. In spite of these, the fracture toughness, which ranges between 63 and 87 MPa.m0.5, of the SLM-SS is good, which is a result of the mesostructured induced crack tortuousity.Both tensile and toughness properties of SLM-SS were found to be anisotropic in nature. Upon aging SLM-MS, nanoscale precipitation of intermetallic compounds occurs within the cells that, in turn, lead in marked improvements in tensile strengths properties, but substantial reductions in ductility and fracture toughness. Overall, the mechanical performance, except ductility, of the SLM-MS after aging is found to be similar to that of CM-MS. Importantly, the lack of ductility does not lead to a reduction in toughness. Although the SLM-MS alloy possesses a mesostructured, no significant anisotropy in the mechanical behaviour is observed. The unnoticed studies on SLM-AS, -SS, and -MS reveal that the tensile residual stresses, gas-pores, and unmelted powder particles, can degrade the unmatched highest fatigue properties considerably and hence need be eliminated for high fatigue strength. Room temperature, electrochemical corrosion resistances (CRs) of SLM-AS, -SS and -MS in 0.1M NaCl solution were also evaluated and compared with those CM counterparts. While SLM improves CRs of AS and SS, it degrades that of MS. The results are discussed in terms of microstructural refinement and porosity that are common in SLM alloys.
 
Contributor Ramamurty, Upadrasta
 
Date 2018-05-23T17:23:01Z
2018-05-23T17:23:01Z
2018-05-23
2017
 
Type Thesis
 
Identifier http://etd.iisc.ernet.in/2005/3604
http://etd.iisc.ernet.in/abstracts/4473/G28322-Abs.pdf
 
Language en_US
 
Relation G28322