Record Details

Rate Enhancement Of The Catalytic Hydrogenation Of An Unsaturated Ketone By Ultrasonic Irradiation

Electronic Theses of Indian Institute of Science

View Archive Info
 
 
Field Value
 
Title Rate Enhancement Of The Catalytic Hydrogenation Of An Unsaturated Ketone By Ultrasonic Irradiation
 
Creator Mahishi, Shreesha
 
Subject Organic Chemistry
Ultrasonics
Unsaturated Ketones
Hydrogenation
Catalysis
Ketones - Catalytic Hydrogenation
Sonochemistry
Ultrasonic Irradiation
Catalytic Hydrogenation
Ultrasound
Hydrogenation Catalyst
 
Description The aim of the work was to develop an understanding of the phenomenon of rate enhancement observed when a heterogeneous catalytic reaction system is irradiated by ultrasound. The system under investigation was the catalytic hydrogenation of an a, B - unsaturated ketone, using zinc dust and aqueous nickel chloride as a source of hydrogen. When a slurry of zinc particles and aqueous nickel chloride is stirred or sonicated, nickel deposits in the form of patches on the surface of the zinc particles and simultaneously, zinc dissolves into the solution in the form of zinc ions, a process called pitting corrosion.

Hydrogen atoms are formed when hydrogen ions diffuse from the bulk, adsorb onto the nickel surface and take up electrons generated by the dissolution of zinc. Once the atoms are formed on the surface, the atoms combine to form hydrogen molecules, which desorb in the form of hydrogen gas. When ketone is added to this slurry, the hydrogen atom formed on the surface of nickel is used as the source of hydrogen for the hydrogenation reaction. In these processes, nickel serves as catalyst. The ketone first has to diffuse to the bulk, adsorb onto the surface of nickel and undergo reduction by the hydrogen atoms to form the product. The product then has to desorb from the surface and diffuse into the bulk, in order to create vacant sites on the nickel surface for the adsorption of more ketone.

Experiments dealing with measurements of hydrogen evolution rates pointed out that hydrogen is not a limiting reactant, since evolution was sustained for long periods of time. The evolution rates versus time data revealed that the nature of the plots for both, the stirred and sonicated systems were similar. These facts lead us to infer that the basic mechanism of nickel deposition, pitting corrosion, etc. was similar for the two cases.

To study the hydrogenation reaction, experiments were first conducted keeping the nickel catalyst surface area constant. The results of these experiments showed that the hydrogenation reaction can be explained by a first order mechanism. Changing the speed of the stirrer did not effect the rate of the reaction; hence it was inferred that the reaction was not external mass transfer controlled. It was also seen that there was an no significant difference in reaction rates between the stirred and sonicated systems. Hence we conclude that sonication does not effect any process involved in the actual process of hydrogenation, i.e., adsorption, desorption, surface reaction, etc., do not get effected.

It was concluded that the observed rate enhancements of similar compounds in the same system occur only when nickel catalyst is being continuously formed. This is possible only if irradiation with ultrasound enhances the rate of formation of the surface area of the nickel deposit. To study this phenomena, experiments were conducted with continuous formation of nickel catalyst. These experiments were conducted in three ways - stirring with zinc dust, sonication with zinc dust and stirring with presonicated zinc dust. For the first two kinds of experiments, the rates were low, increased to a maximum value and then decreased, but the nature of the third kind of experiments were different. The initial rates were very high as compared to either of the other two kinds of experiments but the rate rapidly reduces and becomes comparable to the rates obtained by stirring with zinc dust. We conclude that sonication creates many active sites on the surface of the zinc particles in the form of crystal defects, which are perhaps necessary for the deposition of nickel. When presonicated zinc particles are used, there are large numbers of these sites and these get consumed rapidly when stirred with aqueous nickel chloride solution. In this work, we do not deal with this case.

In the case of sonication with zinc dust, these active sites are continuously created and are consumed by nickel deposition. For the stirred system, these sites are quite small to start with and new ones are not generated since there is no irradiation by ultrasound. Hence, the rates in the latter case are low for both nickel deposition and the hydrogenation reaction.

In the model, it was assumed that the rate of increase of surface area of nickel, characterized by a specific rate term k z, was proportional to the amount of nickel in the bulk and also to the amount of free zinc surface area available. Similarly, nickel which deposits on previously deposited nickel (characterized by another specific rate constant, kn) was proportional to the amount of nickel in the bulk, the nickel area already deposited and also the free zinc surface area available.

The model is in excellent agreement with the experimental data obtained. The model predicted higher values of kn and kz for the sonicated system, indicating that the rate of deposition of nickel is much higher in this case than for the stirred system. Moreover, the model also predicts that the deposit in the case of a sonicated system is thinner and flatter, since it was seen that the surface area created for the same amount of nickel deposited was much higher in this case than the stirred system.
 
Publisher Indian Institute of Science
 
Contributor Kumar, R
Gandhi, K S
 
Date 2005-08-25T09:00:46Z
2005-08-25T09:00:46Z
2005-08-25T09:00:46Z
1996-08
 
Type Electronic Thesis and Dissertation
 
Format 2749182 bytes
application/pdf
 
Identifier http://etd.iisc.ernet.in/handle/2005/138
null
 
Language en
 
Rights I grant Indian Institute of Science the right to archive and to make available my thesis or dissertation in whole or in part in all forms of media, now hereafter known. I retain all proprietary rights, such as patent rights. I also retain the right to use in future works (such as articles or books) all or part of this thesis or dissertation.