Record Details

Study Of Friction And Wear Behaviour Of Nano-Embedded Aluminium Alloys

Electronic Theses of Indian Institute of Science

View Archive Info
 
 
Field Value
 
Title Study Of Friction And Wear Behaviour Of Nano-Embedded Aluminium Alloys
 
Creator Bhattacharya, Victoria
 
Subject Metallurgy
Aluminium Alloys
Tribiology
Wear
Nanomaterials
Alloy Preparation
White Metal Bearings
Babbit
Aluminium-Lead Alloys
Aluminium-Indium Alloys
Aluminum-Bismuth Alloys
Bearing Alloys
 
Description In general, the bearing alloys have two types of microstructure i.e., either a soft matrix with discrete hard particles or a continuous matrix of the harder metal with small amount of the softer metal finely dispersed in it. The aluminium and copper based bearing alloys which are widely studied fall in the second category. However, the bearing materials which have been studied have micron sized dispersoids. In recent times, it is possible to produce nanoscale dispersoids in a hard matrix by the novel processing route of rapid solidification. This offers an opportunity to study the small length scale effect on tribological processes. In this thesis, we deal with aluminium alloys where nanoscaled dispersions of lead, bismuth and indium are produced by rapid solidification processing. Chapter 1 of the thesis is an introduction, followed by Chapter 2, which reviews the literature on nanomaterials. Special attention is given to the monotectic system, followed by a brief description on friction and wear of materials which is necessary for our present investigation. The details of experimental and characterisation techniques are given in Chapter 3. In Chapter 4, we present a brief study of white metal bearings (babbit). Tin-based babbit of composition, Sn-6wt% Cu-llwt% Sb was studied. The study of babbit was mainly carried out with the idea that it could serve as a benchmark for subsequent studies in aluminium alloys, in terms of tribological properties. In particular, we have carried out a detailed electron microscopic investigation on the phases present in the bearing alloy. The friction and wear behaviour of this material confirms the proper calibration of our setup for wear studies. This is followed by a detailed study on the synthesis, microstructure and tribological behaviour of nanodispersed aluminium alloys, Al-6wt% Pb and Al-10wt% Pb in Chapter 5.

For comparison, we have also studied melt-spun aluminium without dispersoids. Detailed electron microscopic characterisation indicates that lead has a cube on cube orientation relationship with the aluminium matrix, and the particles exhibit a lognormal distribution with the mode of the particle size distribution being 15 nm. The pin on disc results suggest a distinct lowering of coefficient of friction corresponding to pure aluminium (μ= 0.40) and as cast aluminium-lead alloys (μ= 0.41). Detailed SEM studies indicate a tribolayer consisting primarily of Al, Pb and Fe. The later comes from the counterface material. Our results clearly indicate that at an early stage, little or no oxidation takes place at the sliding interface. TEM observations indicate significant deformation of lead particles in the sub-surface region. The observations suggest spreading of the lead, which acts as a lubricating layer. Wear behaviour is primarily adhesive and follows Archard's wear law. However, the rate of wear is less than that reported by other investigators on micronsized lead dispersions in aluminium. In Chapter 6, we present the results for alloys dispersed with nanosized indium and bismuth. We show that indium particles on melt-spinning exhibit both cubic and tetragonal crystal structure. The indium particles are coarser (with a mode of 25 nm) than the lead and bismuth particles (which have mode of 15nm). The bismuth containing alloys have a lower wear rate and coefficient of friction compared to lead and indium alloys. However, both indium and bismuth particles do not follow Archard's wear law and the wear vs load graph shows a non-linear behaviour. The results are discussed in terms of known mechanisms of the coefficient of friction and wear. Chapter 7 gives the salient conclusions while in Chapter 8 we discuss some of the unanswered questions and the potential for future work in this field.
 
Publisher Indian Institute of Science
 
Contributor Chattopadhyay, K
 
Date 2005-12-22T08:56:19Z
2005-12-22T08:56:19Z
2005-12-22T08:56:19Z
2000-08
 
Type Electronic Thesis and Dissertation
 
Format 8380980 bytes
application/pdf
 
Identifier http://etd.iisc.ernet.in/handle/2005/190
null
 
Language en
 
Rights I grant Indian Institute of Science the right to archive and to make available my thesis or dissertation in whole or in part in all forms of media, now hereafter known. I retain all proprietary rights, such as patent rights. I also retain the right to use in future works (such as articles or books) all or part of this thesis or dissertation.