Record Details

Corrosion behavior of pure magnesium processed by accumulative roll bonding for biomaterial application<br />

Online Publishing @ NISCAIR

View Archive Info
 
 
Field Value
 
Authentication Code dc
 
Title Statement Corrosion behavior of pure magnesium processed by accumulative roll bonding for biomaterial application<br />
 
Added Entry - Uncontrolled Name Purnamasari, Indah Suis ; Metallurgical Engineering, Faculty of Engineering, Universitas Sultan Ageng Tirtayasa, Banten 42435, Indonesia
Rifai, Muhammad ; Center for Science and Technology of Advanced Material, National Nuclear Energy Agency, Banten 15314, Indonesia
Ajiriyanto, Maman Kartaman ; Center for Technology of Nuclear Fuel, National Nuclear Energy Agency, Banten 15314, Indonesia
Alhamidi, Ali ; Metallurgical Engineering, Faculty of Engineering, Universitas Sultan Ageng Tirtayasa, Banten 42435, Indonesia
Mujamilah, Mujamilah ; Center for Science and Technology of Advanced Material, National Nuclear Energy Agency, Banten 15314, Indonesia
Insani, Andon ; Center for Science and Technology of Advanced Material, National Nuclear Energy Agency, Banten 15314, Indonesia
Prasetya, Ahadi damar ; Center for Science and Technology of Advanced Material, National Nuclear Energy Agency, Banten 15314, Indonesia
Center for Science and Technology of Advanced Materials
 
Uncontrolled Index Term magnesium; deformation; implants, corrosion
Magnesium, Accumulative roll bonding, Implant, Heat treatment, Corrosion rate
 
Summary, etc. <p style="text-align: justify;">Magnesium is one of the materials that can be used as an implant for the human body. It is because the daily intake ofmagnesium for an adult is 240-420 mg/day. Also, the elastic modulus (41 – 45 GPa) and density (1.74 g/cm3) of magnesiumis closer to that of natural bone. However, pure magnesium in the as-cast condition has a very fast corrosion rate,2,89mmPY in 0.9% NaCl solution. Accumulative roll bonding (ARB) is done in this recent study to improve the corrosionrate of pure magnesium. ARB is one of the severe plastic deformations (SPD) method, which provides the possibility toobtain high strained materials without a macroscopic change after a cyclic roll-bonding process (stacking, preheating androlling). Magnesium is annealed at 250°C and 350°C for 25 minutes, and then the ARB process is done with variation; one,two, three and four cycles. The composition was tested using SEM-EDS, showing that the content of a pure magnesiumplate (as annealed) is 99.77%. The grain size is observed using the optic microscope and measured by ImageJ, while thecorrosion rate was measured with an electrochemical and immersion test. The result showed the smallest grain size achievedis 7.204 ± 1,185 μm and that the lowest corrosion rate is 0,0012mmPY. The polarization resistance determined the thicknessand the ability of passivation area obtained with the increasing number of ARB cycles. The higher plastic deformation isrecommended for improve the corrosion resistance of the metallic material for future works.</p>
 
Publication, Distribution, Etc. Indian Journal of Engineering and Materials Sciences (IJEMS)
2022-03-21 14:38:47
 
Electronic Location and Access application/pdf
http://op.niscair.res.in/index.php/IJEMS/article/view/43477
 
Data Source Entry Indian Journal of Engineering and Materials Sciences (IJEMS); ##issue.vol## 28, ##issue.no## 6 (2021): IJEMS-December 2021
 
Language Note en
 
Terms Governing Use and Reproduction Note Except where otherwise noted, the Articles on this site are licensed under Creative Commons License: CC Attribution-Noncommercial-No Derivative Works 2.5 India © 2015. The Council of Scientific &amp; Industrial Research, New Delhi.